Hot Water Systems Castle Hill
Do you need a licensed plumber to fix your hot water system? For repairs and replacements of Australia’s leading hot water systems, we are able to provide same-day service.
Get A Free Quote
We Are Available To Serve You In Castle Hill
Electric, gas or solar hot water system repairs can be completed by our qualified and licensed plumbers, gasfitters and electricians. Heat pumps and other appliances can also be supplied, installed and repaired. Our authorized service representatives have over 30 years of experience, so even if your hot water system is out-of-production, you can count on them to provide you with maintenance and repairs.
In addition to repairing and installing all the leading hot water systems, we also provide installation and service for these brands:
Common Hot Water Plumbing Repair Issues
As a possible way to help you address common problems with your hot water heater and possibly save you time and money, we have put together some troubleshooting tips for emergency plumbing repairs.
- Excessive water flow from the temperature pressure relief valve (TPR)
- Leaking hot water cylinder
- Insufficient hot water flow
- There is no hot water in my system
It is always recommended that you use the services of a professional if you are uncertain of your ability to check your hot water system safely. This is because when your hot water is not running efficiently, it will cost you money. A professional plumber from Plumber Castle Hill should inspect your hot water system. Whether you’re looking to fix a leaky faucet or replace a busted pipe, our fully certified technicians can help.
Emergency Hot Water Heater Repair
Plumber Castle Hill knows how big of an inconvenience it is when your hot water heater isn’t working. That’s why Plumber Castle Hill provides 24 hour service when you require emergency replacement.
If you’re having problems with your hot water heater, we’ve put together some troubleshooting tips that might help. These could save you time and money. If your problem persists, call Plumber Castle Hill’s 24 hour service for an emergency plumber same day service call.
Excessive water flow from the temperature pressure relief valve (TPR)
Sediment may be built up under the valve seat, causing water to run from the overflow valve. This can indicate that the water temperature or pressure is too high. To operate the valve, follow the instructions on the water heater labeling. Carefully lift the lever to allow water to flow from the overflow pipe, making sure that others are clear of the pipe drain, as the water may be hot. Allow water to flow from the overflow pipe for a few seconds, then ease the lever closed. The flow of water should stop. If water continues to flow, call Plumber Castle Hill to book an appointment with one of our authorized service representatives.
Insufficient hot water flow
Is your water heater not working? Check to see if the isolation valve is turned to the “on” position. It may have a black knob or a tap type head and is usually located at a lower level than the water heater inlet. Keep your hands off any other valves associated with the water heater.
Leaking hot water cylinder
A leaking cylinder typically means that a new hot water system is needed – Plumber Castle Hill can replace it for you. To keep using other household appliances, follow the instructions below to turn off the water supply to the hot water system. At the isolation valve (usually at a lower level near the water heater inlet), turn the power off at the meter box. For electric systems, look for the fuse switch or circuit breaker labeled as “Hot Water,” “HWS,” or “Water Heater.” As for gas systems, locate the gas supply valve at the water heater (it’s usually a yellow lever) and turn it a quarter-turn clockwise to isolate the gas.
No hot water in my system
If your switchboard’s fuse is blown, replace it with a wire of the correct rating. If the circuit breaker has tripped, reset it to “on.” A blown fuse or tripped circuit breaker usually signifies a problem that should only be fixed by an authorized service representative – call Plumber Castle Hill to schedule a today. Never take off any electrical covers that expose raw terminals or wiring.
Get In Touch With Us!
If your gas water heater isn’t working, check the pilot light to see if it’s still lit. If not, there will usually be step-by-step lighting instructions for different types of gas water heaters on the inside of the front cover panel.. Follow the procedure carefully as instructed. If you’re unsure or not confident with the procedure, don’t attempt to light it and call Plumber Castle Hill for same-day service from one of our authorized service representatives.